Distinct Slapping Noise Coming from Bridgeport Series I 2hp J Head
Hey Guys, I am looking for some feedback on some noise I am getting from my Bridgeport Series I 2hp J Head. I have a distinct slapping noise on my Bridgeport head. I believe it to be the splines or hub...
View ArticleTable moves slightly when locked
I am seeing movement of .0005 - .0015" of movement of the table when I lock the table or saddle. After its locked, there is no movement. The machine is an older series 1 that's been rebuilt. The gibs...
View ArticleLocal Newspaper article on the history of Hardinge
I don't know of any way to permanently link this, but here it is while it lasts..... Elmira history: How Hardinge came to be
View Articlelubrication for my 1928 hardinge cataract
So, I'm a little behind on my time estimate to get it back up and running, but I should be starting to reassembly it in 1-2 weeks, any suggestions on what kind of lube to use during reassembly? what to...
View ArticleHardinge HLV-H Carriage OIl Pump Assembly stuck!
Hi folk I'd like to remove the Oil Lubrication pump assembly to clean and service but sadly it's just stuck solid. Hardinge HLV-H Oil Pump Tried being gentle but not moving so I guess the old oil has...
View ArticleX-Axis Feed Problem...
Good morning everyone... So I'm going to be honest and admit that I think I screwed up! I'm a newbie here and still learning what I'm doing so please, done shame me too bad :-) I have a Series 1 J with...
View Articleez trak on ebay a fraud
There is an ad for an ez trak II on ebay for 15,200 that is a scam. The photos and description come from Rohners equipment that was sold back in January.
View ArticleClik here to view.
how does this refurb look?
just finished this baby, new spindle bearings (and others, as needed), belts (of corse), X and Y nuts, and everything that fit in the bransonic 7000 blasted... Attached Thumbnails
View ArticleTopic - PM classifieds regarding the 1994 Hardinge HLV-EM that be on interest...
http://www.practicalmachinist.com/vb...e-sell-341630/
View ArticleBridgeport 2J2 problem
Hi everyone, I have changed my drive belt and checked pulley bushes etc and all appears fine. However after adjusting the back gear selector in high normal direction all is quiet and acceptable but...
View ArticleMilling machine power feed controller advice
Have Excello 602 mill with factory power feed on X but missing control box. Wondering what yall would advise using to control it? Variable speed, forward, reverse and stop would be nice. 120V 1ph...
View ArticleBridgeport J (step) head motor upgrade?
Hello everyone I'm new to machining, purchased an older BP J step head w/1 hp motor. I have been doing research to see if it is possible to install a 2 hp motor onto it. I've that I will need to look...
View ArticleClik here to view.
Hardinge HLV new owner requiring information and help
Hi folks, Im new to the forum and have recently (yesterday) bought a Hardinge HLV. Ive identified the s/n to be HLV 0186 and is a British built machine. What age does this make the machine? The...
View ArticleBridgeport R2E4 - Unacceptable Backlash in X axis
I've discovered that my Bridgeport R2E4 has 3-5 thou backlash in the X axis. The Y axis also had some backlash (3 thou), but after tightening the gibs, it is down to 1 thou. Tightening the gibs on the...
View ArticleHardinge lathe?
Looking to find out information about a hardinge lathe with serial number from the head stock A.E.C.-O.R.N.L. X-83607. Need a new swivel plate for the compound rest. Have not been able to find...
View ArticleClik here to view.
Bridgeport Series 1 Textron w/power feed - 3 phase Delta Wiring Question
I recently purchased a Bridgeport Series 1 milling machine with power cross feed. I believe it was made in the late 70's or early 80's. Textron manufactured the electronics for it and I am seeking...
View ArticleNewbie here saying hi and have a question
Good day all, My name is Pete and I am a general machinist for over 30 years now. I'm into building streetrods and currently run a 1925 ford model t tow truck and have a 1935 ford Tudor that is next...
View ArticleClik here to view.
Romi/Bridgeport/DoAll 13-5 Lathe Feed Issue
Hey guys, I have a Romi 13-5 (same as a DoAll 13-5 or the sometimes Bridgeport labeled machine). My issue is that the longitudinal feed is not working. Cross feed works just fine. The lever that...
View Articley-axis lock not working
Hi,I just purchased my first Bridgeport mill. It is a 1987 J head and seems to be in pretty good condition.The only problem I have so far is that the y-axis lock doesn't work. Unlike the x-axis lock it...
View ArticleBridgeport #2 boring head instructions
Does anyone have a link for a instruction manual on Bridgeport boring heads? I know how to use the head, but was wondering if it was recommended to tighten the single dovetail screw after adjusting the...
View Article